Dongguan MUMU Woodwork Co., Ltd. is one of the leading manufacturers and suppliers of wooden 3d wave wall panels in China, also supports customized service with low price. Welcome to wholesale discount wooden 3d wave wall panels for sale here from our factory. If you have any enquiry about quotation and free sample, please feel free to email us.
Solid Wood · 3D Wall Panel
Wooden 3D wave wall panels are solid wood interior boards with a continuous S-shaped wave profile running the length of the plank. The standard board is supplied at W180 × D16 × H2800 mm in natural solid olive wood and white wood, joined edge to edge with a V-joint tongue and groove system, and used as decorative interior wall cladding in hotels, clubs, shopping malls, bars, office buildings and home decoration. Dimensions are customizable to project sizes.
Material
Dimension
Pattern
Joint
Wooden 3D Wave Wall Panels
|
What Are Wooden 3D Wave Wall Panels?
A wooden 3D wave wall panel is a decorative wall board whose face is shaped into a repeating S grain groove rather than left flat. The wave runs along the 2800 mm length of the plank, so when boards are set side by side the peaks and troughs read as one continuous undulating surface across the whole wall rather than as separate panels.
The three-dimensional effect comes from light, not from print. Because the surface alternates between raised crests and recessed grooves, any grazing light - a wall washer, a cove detail, daylight from a side window - throws a soft shadow into each trough. The same wall reads differently through the day, which is why this profile is specified for reception walls and background walls where a flat finish would look inert.
The panels are cut from solid wood, so the wave is machined into real timber and the grain follows the contour of the profile. This is the visible difference between a solid wood wave board and a printed or embossed MDF wave pattern panel, where the texture is pressed into a board and the grain image is applied to the surface.
Wave Compared With Other 3D Wall Panel Textures
Within the 3D wall panel family, the wave profile sits between two more common textures and behaves differently from both.
- Wave against flutes. Fluted wood wall panels use straight parallel ribs with hard edges and a repeating vertical rhythm. The wave profile has no straight line in it; the surface curves continuously, so the shadow gradient is soft instead of banded.
- Wave against slats. Wood slat wall panels are separate battens with open gaps between them, usually mounted on a felt or board backing. The wave board is a single closed surface with no air gap, which is why it is joined by tongue and groove rather than fixed to a backing sheet.
- Wave against relief carving. A carved wavy solid wood wall panel can carry an irregular or asymmetric wave designed for a single wall. The S grain groove used here is a regular repeating profile, which makes it easier to specify by the square metre and to extend across a long run.
Product Highlights
Wall Decor Product
The solid wood wall panel is an environmentally friendly and durable product that has been widely used as interior wall decoration material. This exclusive, elegant, stylish wooden wave board panels provide a great solution to ugly, problematic and unfinished walls.
Widely Use
This decorative material is mainly used in decoration projects such as hotels, clubs, home decoration, shopping malls, etc. It is especially suitable for designing background walls, TV walls, bars and etc.
Easy Installation
Wooden 3D Wave wall panels are installed with V-joint tongue and groove method which giving a uniform flat surface and strength after joint. This is the most popular traditional panel cladding systems by providing a clean surface with a little shadow line between the boards.
Wood Species, Grain and Natural Colour Variation
The standard specification is natural solid olive wood and white wood in a natural wooden colour, supplied without a pigmented coating so the timber's own figure stays visible. Because every board is cut from real timber, colour will vary from plank to plank and small knots, mineral streaks and grain reversals occur. This is a characteristic of solid wood wall panels, not a defect, and it is the reason a wave wall reads as a natural material rather than a printed one. On large walls, boards are normally shuffled during setting out so that light and dark planks are distributed instead of grouped.
Alternative species are quoted case by case. Oak is the usual request where a light, open-grained wall is wanted, and walnut where the brief calls for a darker, more even tone.
Timber moves with the humidity of the room it sits in. Panels should be ordered against the conditions of the finished space, and the moisture content of the boards on delivery should be checked against site conditions before fixing, since installing dry boards into a damp shell or damp boards into a heated shell is the most common cause of wood cracking and open joints later.
Surface Finish Options
Three finishing routes are used on this profile:
Oiled
A penetrating finish that keeps the surface matte and leaves the grain open to the touch, which suits a wave profile because it does not fill the base of the groove.
Lacquered
A film-forming finish that gives a harder, more wipeable surface for high-traffic walls in malls, bars and hotel corridors.
Unfinished
Boards supplied raw for stain or coating on site, where the wall has to be matched to joinery finished by others.
The practical trade-off between the first two routes is repairability against durability, and the difference between wood wax oil and varnish decides how a scuffed panel is repaired: an oiled surface can be spot-sanded and re-oiled in place, while a lacquered surface usually has to be recoated across a whole board. Where a wall has to be recoloured later, note that a carved wave surface is harder to coat evenly than a flat one and 3D wall panels are best painted by spray rather than by roller.
Where Wooden 3D Wave Wall Panels Are Used
Hotel lobbies and reception desks
A full-height run behind the desk, lit from a slot above, so the wave carries the shadow line down the whole wall.
Restaurants, bars and clubs
Used along a long wall to break up its length without adding depth to the plan, and to soften hard rooms full of glass, tile and stone.
Office reception and meeting rooms
A warm timber accent wall behind the logo wall or the video-call backdrop.
Residential living rooms
Most often as a TV background wall, where the recessed grooves also help disguise cable routes behind the boards.
Bedrooms
Run horizontally behind the bed as a headboard panel, either to bed width or wall to wall.
Ceilings
The same profile can be turned onto the soffit, though 3D wall panels used on a ceiling need mechanical fixing rather than adhesive alone.
Installation of Wooden 3D Wave Wall Panels
The V-joint tongue and groove method described above is a dry-jointed cladding system: each board's tongue enters the groove of the next, and the chamfer on the edge leaves a fine shadow line that absorbs small variations between planks. A typical sequence runs as follows.
Acclimatise
Leave the boards unwrapped in the finished room for several days before fixing, so the timber reaches the humidity it will live in.
Check the substrate
The wall must be dry, sound and flat. Hollows behind a rigid board will telegraph through as an uneven wave line.
Set out
Decide the direction first. Vertical boards emphasise height and let the 2800 mm length run floor to ceiling with no cross joint; horizontal boards widen a room but need the wave to line up across every joint, so the run should be dry-laid before fixing.
Fix
Boards are bonded to the wall, secret-nailed through the tongue, or fixed to timber battens where the wall is out of true. On battened walls the counter-battens must be spaced closely enough that the board cannot flex between them. Choice of adhesive matters on a profiled board, because only the flat back face is in contact with the wall.
Cut and trim
Cut with a fine-tooth blade, face up, to avoid breakout on the crest of the wave. Sockets and switch plates are cut from the back and finished from the face.
Close the edges
Internal corners are butted or scribed, external corners mitred or capped with a matching trim, and a movement gap is left at floor and ceiling and covered by the skirting or shadow gap.
The general installation procedures for solid wood wall panels apply to this profile as well, with the one addition that pattern alignment has to be planned before the first board goes on the wall.
Customization
The standard board is W180 × D16 × H2800 mm and the dimension is customizable. Items that are normally confirmed at drawing stage:
- Panel length and width, cut to the setting-out drawing so that the wall finishes on a full board rather than a narrow off-cut
- Wood species
- Colour and finish level
- Edge treatment, where a run has to terminate against glass, stone or a shadow gap instead of another board
Packaging, Delivery and Maintenance
Panels are supplied in export standard packing, or packed to the customer's own requirements. Long profiled boards are the most damage-prone item on a joinery shipment, so the crest of the wave and the tongue and groove edges are the two points that need protection in transit. On arrival, boards should be stored flat and off the floor in the building they will be installed in, not left standing against a wall or stored in an unheated area.
Dust settles in the troughs of a wave profile faster than it does on a flat wall, so routine care is a soft brush attachment or a dry microfibre cloth drawn along the direction of the groove rather than across it. Avoid soaking the surface, and keep abrasive cleaners and silicone polishes off the finish. The general guidance on maintenance and cleaning of wood wall panels applies, with the profile making the direction of wiping the one thing worth getting right.
Wooden 3D Wave Wall Panels - FAQ
Q: Are the panels solid wood or veneer?
A: Solid wood. The standard material is natural solid olive wood and white wood, and the wave is machined into the timber rather than pressed or printed onto a substrate.
Q: What is the standard panel size?
A: W180 × D16 × H2800 mm. The dimension is customizable, so panels can be produced to a project setting-out drawing instead of being cut down on site.
Q: Can the panels be installed horizontally as well as vertically?
A: Yes. Vertical installation runs the 2800 mm length floor to ceiling with no cross joint and emphasises height. Horizontal installation widens a room but requires the wave to align across every board joint, so the run should be dry-laid and set out before fixing.
Q: How do the boards join together?
A: With a V-joint tongue and groove profile. The tongue of one board enters the groove of the next to give a uniform flat surface, and the chamfered edge leaves a fine shadow line between boards.
Q: Are wooden 3D wave wall panels soundproof?
A: The sculpted face diffuses reflected sound inside a room, which is why hard rooms feel calmer after the wall is clad. It is not a sound insulation product and it does not stop sound passing between two rooms. Where a measured acoustic value is required, a slotted or perforated board with an absorbent backing should be specified instead.
Q: Can the panels be used in bathrooms or other humid rooms?
A: This is a solid timber interior board and it moves with the humidity of the room. It is intended for dry, conditioned interior spaces. Splash zones, unheated areas and rooms with sustained high humidity are outside its normal use.
Q: Will there be colour variation between boards?
A: Yes. Natural timber varies in tone and figure from board to board, and small knots and grain reversals occur. Boards are normally shuffled during setting out so the variation is distributed evenly across the wall.
Q: How long do the panels last?
A: Service life depends far more on the room and the finish than on the profile. Kept in a dry, conditioned interior and recoated when the finish wears through, a solid timber wall lasts as long as the joinery around it; the general question of how long 3D wall panels last comes down to substrate stability, humidity control and finish maintenance.
Q: What is needed to prepare a quotation?
A: Wall elevations with dimensions, the required species and finish, the installation direction, and whether trims for corners and reveals are included in scope.
Request a sample or project quotation
Our 3D wave wood wall panels are all custom-made products. Prices depend on the wood type, panel size, surface treatment, and quantity. Please provide your information, and we will provide you with a written quotation, including the unit price, wall panel layout diagram, and confirmed production lead time.
Hot Tags: wooden 3d wave wall panels, 3d wood wave wall panel, solid wood wave wall panel, wave wood wall cladding, 3d wood wall panels, tongue and groove wood wall panel, custom wood wall panel, interior wood wall cladding, Wood Wall Panel